GasAlertMax XT II Sampling/Testing Equipment And Spares

BW Technologies Replacement Pump Kit

BW Technologies creates and manufactures a wide range of advanced gas detection devices. These devices have a long life and require little maintenance. However, to extend the lifespan and ensure functional operation, regular inspection and occasional maintenance is necessary. For this reason, BW Technologies also manufactures a range of replacement parts that are compatible for the gas detection systems. The BW Technologies Replacement Pump Kit easily replaces old or outdated pumps. This replacement pump kit is compatible with the GasAlertMax XT II gas detector and is built to last.

Part Number: XTRPUMPK1

Part Number: XTSS1

BW Technologies Quad Sensor Screen Filters (kit of 10)

To extend the lifespan of your BW Technologies gas detection instrument, proper inspection and maintenance is required. When inspecting the device, be certain to regularly check the conditions of all filters. A clean filter will help to protect the device by preventing debris, dust, and moisture from entering the device, sensor, or pump. The Quad Sensor Screen Filters are compatible with certain BW Technologies devices (please check your device's product specifications sheet for compatible) and is available in a pack of 10 screen filters.

Part Number: XTSSK2

Part Number: XTSS

XT-SS-K1 Quad Sensor Screens (Kit of 10)

When your sensor screens become dirty they can block gasses from making contact with the sensors, thus rendering your instrument non-functional. You should visually inspect your filters on a regular basis and when you notice excessive dirt or any type of blockage the instrument should not be used until a new filter is installed. This kit of 10 is perfect to have on hand insuring that you will always have a replacement available.

BW Technologies Sample Probe and Hydrophobic and Particulate Filters

This portable accessory by BW Technologies is easy to use when on the job site. Use this accessory for pick hole sampling or when attempting to sample gas in hard to reach spaces. This particular sample probe has the added benefit of utilizing hydrophobic and particulate filters which help to moisture and debris from entering the detector and damaging its internal circuitry. For a list of BW Technologies accessories that are compatible with your gas detector, please see your product's specifications sheet.

Part Number: GAPROB11

BW Technologies Filter and Gasket Replacements for Sample Probe

BW Technologies provides a wide range of replacement parts and accessories for its product lines. Amongst its many equipment accessories are the BW Technologies Filter and Gasket Replacements for Sample Probe. The replacement hydrophobic filters and particulate filters work to prevent moisture and debris from entering the gas detection instrument. BW Technologies makes a range of replacement parts for their products. Consult your product's specifications sheet to determine which parts are best for you.

Part Number: GAPROBFILK1

BW Technologies Quick Connect Fitting Spares for Hoses

The BW Technologies Quick Connect Fitting Spares for Hoses comes in a kit of 2 spares. With the spares, users can easily connect the tubing to the inlet pump on the BW Technologies device. This replacement part is manufactured to be compatible with portable BW Technologies’ detector hoses. Each connect fitting spare is made with durable material that provides an impenetrable seal while protecting the integrity of the hose and the accuracy of the data. To ensure compatibility, please check your device’s specification sheet.

BW Technologies Collapsible Sampling Probe with Handle

This particular attachment is ideal for pick hole sampling and for drawing samples in hard to reach places. This collapsible sampling probe is approximately 3.3 feet (1 meter) in length. The probe has a comfort grip that helps to ensure proper use when in hazardous conditions. The attachment also easily collapses into a compact and portable travel unit. When collapsed, the device can easily fit into a utility belt or pocket. To determine whether or not the BW Technologies Collapsible Sampling Probe with Handle is compatible with your device, please consult the product specification sheet.

Part Number: GACPROB1

BW Technologies Collapsible Sample Probe with Handle (6 feet)

BW Technologies manufactures a range of accessories, attachments, and replacement parts for its devices. To help improve the usability of its detectors, BW Technologies also produces various probes. The BW Technologies Collapsible Sample Probe with Handle extends to approximately 6 feet and can easily fold into a compact unit that will easily fit in a utility belt, work bag, or pocket. This sample probe also has a comfort grip handle for ease of use.

Part Number: GACPROB2

BW Technologies Search Probe with Handle and Quick Connect

The BW Technologies search probe with handle and quick connect is approximately 1 foot in length. The attachment allows users to easily and accurately sample remote locations. Using quick connect, users can easily attach the tubing to the pump inlet for fast sampling. The connect feature is durable and secure to ensure the integrity and accuracy of the sample. The probe also has a comfortable hand grip that allows for easy maneuvering and measuring.

Part Number: D4PROB1

BW Technologies Sample Probe with Handle and Quick Connect (3 feet)

For sampling in remote or hard to reach locations, BW Technologies manufactures a range of sampling probes that assist users with this task. The sample probe with handle and quick connect is approximately 3 feet long and features a comfortable grip handle to ensure maximum maneuverability. The quick connect feature allows users to quickly and easily connect the tubing to the pump inlet. The quick connect seals the connection site and protects the integrity of the device and its readings.

Part Number: D4PROB3

BW Technologies Search Probe with Handle and Quick Connect (6 feet)

BW Technologies manufactures an assortment of detector accessories, attachments, and replacement parts. With the accessories and attachments, users can easily customize their device to meet their individual needs. As part of its accessories line, BW Technologies manufactures various probes with differing specifications. This particular probe is approximately 6 feet long and is ideal for sampling in remote or hard to reach locations. The unit has an easy grip handle and a quick connect feature that allows users to easily and instantly connect the hose to the pump inlet. The quick connect seals the location and helps to prevent leaks.

Part Number: D4PROB6

BW Technologies Telescopic Sample Probe (7.9 feet)

The BW Technologies Telescopic Sample Probe allows users to easily and quickly draw samples from a distance. This particular probe is approximately 7.9 feet long (or 2.4 meters). With such a range, users can remain at a safe and comfortable distance while easily drawing samples. This probe is compatible with a number of BW Technologies gas detectors and devices. To determine whether or not the Telescopic Sample Probe meets your needs, please review your device's specifications sheet.

Part Number: GATPROB7

BW Technologies Sampling Float

The BW Technologies Sampling Float is the most suitable accessory for drawing samples of air directly above liquids. This easy to use solution has a hose that connects between two flotation devices and connects to the sampling device. The sampling inlet is purposely elevated above the liquid. This sampling float is an easy sampling solution by BW Technologies designed to increase usability and onsite user friendliness. Please consult your product specification sheet for more instruments that are compatible with your product.

Part Number: GAFLOAT

BW Technologies Metallic Sintered Particulate Filter

Accessories made by BW Technologies are guaranteed to be reliable and effective. The company produces a wide variety of replacement parts and accessories to fit most needs for their products. The BW Technologies Metallic Sintered Particulate Filter is a durable sintered cylinder filter that prevents dirt and debris from damaging, entering, and clogging the pump. This filter is compatible with a range of BW Technologies products. Please consult your product specifications sheet to determine if this filter is compatible with your device.

Part Number: GAMFILTER

Part Number: M5-AF-K2

Part Number: M5-AF-K2-100

BW Technologies Hydrophobic Pump Filter Replacement (Kit of 5)

BW Technologies manufactures some of the most advanced portable and personal gas detectors in the world. The company also produces a range of accessories, attachments, and replacement parts that help to extend the lifespan of their advanced portable gas detectors. For devices utilizing a hydrophobic pump, BW Technologies offers their Hydrophobic Pump Filter Replacement Kit. The replacement filters easily fit inside the device and work to protect the detector from moisture and debris. This specific kit has 5 filters.

Part Number: XTRFH5

BW Technologies Hydrophobic Pump Filter Replacement (Kit of 50)

For BW Technologies portable gas detection devices that operate with a hydrophobic pump, BW Technologies produces a range of replacement parts and accessories. The Hydrophobic Pump Filter Replacement Kit offers 50 replacement filters that easily fit inside the BW Technologies gas detection device. Each of this filters are optimally designed to protect the pump and gas detection device from dust, debris, and moisture. These filters help to extend the life of the device and improve its effective operations.

Part Number: XTRFH50

BW Technologies Hydrophobic Pump Filter Replacement (Kit of 100)

For BW Technologies products utilizing a hydrophobic pump, BW Technologies also manufactures a Hydrophobic Pump Filter Replacement Kit. The replacement filters easily fit into the gas detection device and effectively protect the pump and the device from dust, debris, and moisture. This specific kit is available with 100 replacement filters at a very low cost. To determine if this replacement kit is compatible with your BW Technologies device, please consult your device's product specification sheet.

Part Number: XTRFH100

Part Number: GAPFMAX

BW Technologies Particulate Pump Filter Replacement (Kit of 50)

BW Technologies creates a variety of replacement filters for their series of portable gas detection instruments. The Particulate Pump Filter Replacement Kit is complete with 50 particulate pump filters that fit easily into BW Technologies devices. Each circular filter acts to extend the life of the instrument by effectively preventing debris, dust, and moisture from entering the device through the pump. Regular maintenance of the pump and the instrument is required and having spare replacement filters is critical to the unit's long life operations.

Part Number: GAPFMAX50

BW Technologies Particulate Pump Filter Replacement (Kit of 100)

Regular maintenance and inspection is critical to ensuring the accuracy and effectiveness of any BW Technologies portable gas detection instrument. Although these instruments require very minimal maintenance, users should always inspect the filter and the pump. When it is appropriate, users can replace their filters with a BW Technologies replacement filter. Having a clean filter helps to ensure that the device is adequately protected from dust, debris, and moisture. This particular replacement filter kit is compatible with particulate pumps and is available in a kit of 100.

Part Number: GAPFMAX100

DOCK2-2-1C1M-00-G MicroDock II Automatic Test and Calibration Station with GasAlertMax XT II Module (Charging) with Power Supply and 2 Inlets by BW Technologies

BW Technologies by Honeywell has a solid reputation for cost effective, safe, and reliable gas detection and calibration systems. Continuing this trend of excellence, BW Technologies has developed the MicroDock II automated instrument docking station. With multi-language support systems, self-containment, and easy portability, the low cost Microdock II is a great choice for automatic tests and calibrations.

Standard features

The MicroDock II is a hands-free automated calibration and testing system designed to monitor the functions and effectiveness of gas monitoring instruments developed by BW Technologies. The easy to use portable MicroDock II is fully expandable, and can accommodate up to 10 docking modules and 6 charging stations. Once connected, the dock automatically verifies the performance of audible and visual alarms and can calibrate gas detection and measurement. Results of calibration tests and performance measures are automatically recorded. The MicroDock II contains a MultiMediaCard data storage system to provide maximum datalogging and record retention.

Low maintenance

The MicroDock II is a fully functional stand alone automatic test and calibration system. Users do not need to be connected to a computer in order to perform calibration and bump tests. However, the system can be connected via an LAN, and the instrument includes BW Fleet Manager II software for quick and easy data analysis. The instruments long lasting batteries and wall adapter increase the lifespand of the instrument. With limited battery and part replacements, users can rest assured that their investment in the MicroDock II is sure to be sound.

Ease of use

The easy to read instrument display screen and bright LED test indicators ensure maximum readability of test results. The screen provides a real-time clock that displays the time and date of the last calibration and the last bump test, and the LED lights provide unmistakable pass or fail test results . The one button command keys is one of the design features that helps to minimize user training requirements and ensure that the instrument is intuitive and easy to function. Adding additional docking modules to the test station is also simple. Users need only to plug-in connections.

Compatibility

For power, the test system can run on a 6 volt wall adapter or a set of 4 C-cell batteries. The MicroDock II is compatible with a variety of BW Technologies gas monitoring systems including the GasAlertQuatro, GasAlertMax XT II, GasAlertMicroClip, GasAlertMicro 5 Series models, GasAlertClip Extreme (2 and 3 year), and GasAlert Extreme. Users may also purchase an optional wall mount for easy storage. Other optional accessories include the Cal gas wall mount, the MicroDock II portable system kit, demand flow regulator, and network USB. BW Technologies by Honeywell provides a standard 2 year warranty for the MicroDock II.

Worksite managers looking for a high quality, reliable, and low cost automated calibration and test system should look no further than the MicroDock II by BW Technologies. With its simple design, intuitive test result display, and easy to use calibration system, the MicroDock II is the best choice for calibration and testing.

Part Number: DOCK221C1M00G

DOCK2-2-1M-00-G MicroDock II Automatic Test and Calibration Station with GasAlertMax XT II Module (Charging) with No Power Supply and 2 Inlets by BW Technologies

BW Technologies by Honeywell has a solid reputation for cost effective, safe, and reliable gas detection and calibration systems. Continuing this trend of excellence, BW Technologies has developed the MicroDock II automated instrument docking station. With multi-language support systems, self-containment, and easy portability, the low cost Microdock II is a great choice for automatic tests and calibrations.

Standard features

The MicroDock II is a hands-free automated calibration and testing system designed to monitor the functions and effectiveness of gas monitoring instruments developed by BW Technologies. The easy to use portable MicroDock II is fully expandable, and can accommodate up to 10 docking modules and 6 charging stations. Once connected, the dock automatically verifies the performance of audible and visual alarms and can calibrate gas detection and measurement. Results of calibration tests and performance measures are automatically recorded. The MicroDock II contains a MultiMediaCard data storage system to provide maximum datalogging and record retention.

Low maintenance

The MicroDock II is a fully functional stand alone automatic test and calibration system. Users do not need to be connected to a computer in order to perform calibration and bump tests. However, the system can be connected via an LAN, and the instrument includes BW Fleet Manager II software for quick and easy data analysis. The instruments long lasting batteries and wall adapter increase the lifespand of the instrument. With limited battery and part replacements, users can rest assured that their investment in the MicroDock II is sure to be sound.

Ease of use

The easy to read instrument display screen and bright LED test indicators ensure maximum readability of test results. The screen provides a real-time clock that displays the time and date of the last calibration and the last bump test, and the LED lights provide unmistakable pass or fail test results . The one button command keys is one of the design features that helps to minimize user training requirements and ensure that the instrument is intuitive and easy to function. Adding additional docking modules to the test station is also simple. Users need only to plug-in connections.

Compatibility

For power, the test system can run on a 6 volt wall adapter or a set of 4 C-cell batteries. The MicroDock II is compatible with a variety of BW Technologies gas monitoring systems including the GasAlertQuatro, GasAlertMax XT II, GasAlertMicroClip, GasAlertMicro 5 Series models, GasAlertClip Extreme (2 and 3 year), and GasAlert Extreme. Users may also purchase an optional wall mount for easy storage. Other optional accessories include the Cal gas wall mount, the MicroDock II portable system kit, demand flow regulator, and network USB. BW Technologies by Honeywell provides a standard 2 year warranty for the MicroDock II.

Worksite managers looking for a high quality, reliable, and low cost automated calibration and test system should look no further than the MicroDock II by BW Technologies. With its simple design, intuitive test result display, and easy to use calibration system, the MicroDock II is the best choice for calibration and testing.

Part Number: DOCK221M00G

DOCK2-0-1C1M-00-G GasAlertMax XT II / GasAlertMax XT Docking Module (Charging with Power Supply) by BW Technologies

The docking station is compatible with the GasAlertMax XT II detection device and the GasAlertMax XT detection device. The compact and durable unit has front mounted LED indicators to notify users of the status of the docked devices. The docking station also has a power supply that will charge the device once it is inserted into the docking station. An LED indicator will notify users when charging is complete. This docking station provides a cost effective calibration and bump test solution and a full two year warranty.

Part Number: DOCK201C1M00G

DOCK2-0-1M-00-G GasAlertMax XT II / GasAlertMax XT Docking Module (Charging - No Power Supply) by BW Technologies

The BW Technologies GasAlertMax XT II and GasAlertMax XT Docking Module is compatible with both of the named gas detection devices. The docking station provides an easy and cost effective solution to bump test and calibration management. Simply dock the device into the module and the LED indicator will notify users of the testing status of the docked units. This unit does not contain a power supply but has a full 2 year warranty through BW Technologies.

Part Number: DOCK201M00G