1-866-4 JJSTECH(1-866-455-7832)

  1. Home
  2. Honeywell Analytics
  3. SS4 Series
  4. Multi-Spectrum Electro-Optical Digital Fire & Flame Detector (UV / IR & UV)

Multi-Spectrum Electro-Optical Digital Fire & Flame Detector (UV / IR & UV)

Filter by Category
 
Items per page:
Sort by:
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-A2
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-A2




    Item #SS4-A2
    BrandHoneywell Analytics
    Price: $9,617.00
    Quantity:
    Discontinued

    SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-A2-SS
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-A2-SS




    Item #SS4-A2-SS
    BrandHoneywell Analytics
    Price: $6,200.00
    Quantity:

    SS4-A2-SS Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-AS2
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-AS2




    Item #SS4-AS2
    BrandHoneywell Analytics
    Price: $5,396.00
    Quantity:
    Discontinued

    SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-AS2-SS
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-AS2-SS




    Item #SS4-AS2-SS
    BrandHoneywell Analytics
    Price: $6,200.00
    Quantity:

    SS4-AS2-SS Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Nonlatching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT - SS4-AUV2
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Nonlatching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT - SS4-AUV2




    Item #SS4-AUV2
    BrandHoneywell Analytics
    Price: $4,769.00
    Quantity:

    SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Nonlatching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Nonlatching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT - SS4-AUV2-SS
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Nonlatching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT - SS4-AUV2-SS




    Item #SS4-AUV2-SS
    BrandHoneywell Analytics
    Price: $5,346.00
    Quantity:

    SS4-AUV2-SS Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Nonlatching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-A2-M
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-A2-M




    Item #SS4-A2-M
    BrandHoneywell Analytics
    Price: $5,569.00
    Quantity:

    SS4-A2-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-A2-SS-M
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-A2-SS-M




    Item #SS4-A2-SS-M
    BrandHoneywell Analytics
    Price: $6,372.00
    Quantity:

    SS4-A2-SS-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AS2-M
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AS2-M




    Item #SS4-AS2-M
    BrandHoneywell Analytics
    Price: $5,569.00
    Quantity:

    SS4-AS2-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 - SS4-AS2-SS-M
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 - SS4-AS2-SS-M




    Item #SS4-AS2-SS-M
    BrandHoneywell Analytics
    Price: $6,372.00
    Quantity:

    SS4-AS2-SS-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AUV2-M
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AUV2-M




    Item #SS4-AUV2-M
    BrandHoneywell Analytics
    Price: $4,942.00
    Quantity:

    SS4-AUV2-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AUV2-SS-M
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AUV2-SS-M




    Item #SS4-AUV2-SS-M
    BrandHoneywell Analytics
    Price: $6,127.00
    Quantity:

    SS4-AUV2-SS-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-A2-H
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-A2-H




    Item #SS4-A2-H
    BrandHoneywell Analytics
    Price: $6,246.00
    Quantity:

    SS4-A2-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-A2-SS-H
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-A2-SS-H




    Item #SS4-A2-SS-H
    BrandHoneywell Analytics
    Price: $7,049.00
    Quantity:

    SS4-A2-SS-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-AS2-H
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-AS2-H




    Item #SS4-AS2-H
    BrandHoneywell Analytics
    Price: $6,246.00
    Quantity:

    SS4-AS2-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-AUV2-H
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-AUV2-H




    Item #SS4-AUV2-H
    BrandHoneywell Analytics
    Price: $5,284.00
    Quantity:

    SS4-AUV2-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-AUV2-SS-H
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART - SS4-AUV2-SS-H




    Item #SS4-AUV2-SS-H
    BrandHoneywell Analytics
    Price: $5,824.00
    Quantity:

    SS4-AUV2-SS-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx FOR Zone 1 (2) M25 - SS4-A2-C-E
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx FOR Zone 1 (2) M25 - SS4-A2-C-E




    Item #SS4-A2-C-E
    BrandHoneywell Analytics
    Price: $5,543.00
    Quantity:

    SS4-A2-C-E Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx FOR Zone 1 (2) M25 by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 - SS4-A2-CSS-E
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 - SS4-A2-CSS-E




    Item #SS4-A2-CSS-E
    BrandHoneywell Analytics
    Price: $6,346.00
    Quantity:

    SS4-A2-CSS-E Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 - SS4-AS2-C-E
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 - SS4-AS2-C-E




    Item #SS4-AS2-C-E
    BrandHoneywell Analytics
    Price: $5,543.00
    Quantity:

    SS4-AS2-C-E Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 - SS4-AS2-CSS-E
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 - SS4-AS2-CSS-E




    Item #SS4-AS2-CSS-E
    BrandHoneywell Analytics
    Price: $6,346.00
    Quantity:

    SS4-AS2-CSS-E Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx FOR Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-A2-C-E-M
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx FOR Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-A2-C-E-M




    Item #SS4-A2-C-E-M
    BrandHoneywell Analytics
    Price: $5,715.00
    Quantity:

    SS4-A2-C-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx FOR Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx FOR Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-A2-CSS-E-M
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx FOR Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-A2-CSS-E-M




    Item #SS4-A2-CSS-E-M
    BrandHoneywell Analytics
    Price: $6,670.00
    Quantity:

    SS4-A2-CSS-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx FOR Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AS2-C-E-M
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AS2-C-E-M




    Item #SS4-AS2-C-E-M
    BrandHoneywell Analytics
    Price: $5,871.00
    Quantity:

    SS4-AS2-C-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AS2-CSS-E-M
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AS2-CSS-E-M




    Item #SS4-AS2-CSS-E-M
    BrandHoneywell Analytics
    Price: $6,670.00
    Quantity:

    SS4-AS2-CSS-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, IECEx Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AUV2-C-E-M
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, IECEx Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AUV2-C-E-M




    Item #SS4-AUV2-C-E-M
    BrandHoneywell Analytics
    Price: $4,924.00
    Quantity:

    SS4-AUV2-C-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, IECEx Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED FM, cFM, IECEx Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AUV2-CSS-E-M
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED FM, cFM, IECEx Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors - SS4-AUV2-CSS-E-M




    Item #SS4-AUV2-CSS-E-M
    BrandHoneywell Analytics
    Price: $5,461.00
    Quantity:

    SS4-AUV2-CSS-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED FM, cFM, IECEx Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-A2-C-E-H
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-A2-C-E-H




    Item #SS4-A2-C-E-H
    BrandHoneywell Analytics
    Price: $6,393.00
    Quantity:

    SS4-A2-C-E-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-A2-CSS-E-H
    View Product Details >

    Honeywell Analytics SS4-A2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-A2-CSS-E-H




    Item #SS4-A2-CSS-E-H
    BrandHoneywell Analytics
    Price: $7,193.00
    Quantity:

    SS4-A2-CSS-E-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-AS2-C-E-H
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-AS2-C-E-H




    Item #SS4-AS2-C-E-H
    BrandHoneywell Analytics
    Price: $6,393.00
    Quantity:

    SS4-AS2-C-E-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-AS2-CSS-E-H
    View Product Details >

    Honeywell Analytics SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-AS2-CSS-E-H




    Item #SS4-AS2-CSS-E-H
    BrandHoneywell Analytics
    Price: $7,193.00
    Quantity:

    SS4-AS2-CSS-E-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, IECEx Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-AUV2-C-E-H
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, IECEx Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-AUV2-C-E-H




    Item #SS4-AUV2-C-E-H
    BrandHoneywell Analytics
    Price: $5,422.00
    Quantity:

    SS4-AUV2-C-E-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, IECEx Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED FM, cFM, IECEx Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-AUV2-CSS-E-H
    View Product Details >

    Honeywell Analytics SS4-AUV2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED FM, cFM, IECEx Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART - SS4-AUV2-CSS-E-H




    Item #SS4-AUV2-CSS-E-H
    BrandHoneywell Analytics
    Price: $5,959.00
    Quantity:

    SS4-AUV2-CSS-E-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED FM, cFM, IECEx Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimized for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART Factory installed - SS4-AS2-SS-H
    View Product Details >

    Honeywell Analytics Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimized for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART Factory installed - SS4-AS2-SS-H




    Item #SS4-AS2-SS-H
    BrandHoneywell Analytics
    Price: $7,049.00
    Quantity:

    SS4-AS2-SS-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimized for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART Factory installed by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, ATEX, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, ATEX, IECE FOR Zone 1 (2) 3/4 NPT - SS4-A2-C
    View Product Details >

    Honeywell Analytics Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, ATEX, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, ATEX, IECE FOR Zone 1 (2) 3/4 NPT - SS4-A2-C




    Item #SS4-A2-C
    BrandHoneywell Analytics
    Price: $5,543.00
    Quantity:

    SS4-A2-C Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, ATEX, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, ATEX, IECE FOR Zone 1 (2) 3/4 NPT by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, ATEX, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, ATEX, IECE FOR Zone 1 (2) 3/4 NPT - SS4-A2-CSS
    View Product Details >

    Honeywell Analytics Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, ATEX, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, ATEX, IECE FOR Zone 1 (2) 3/4 NPT - SS4-A2-CSS




    Item #SS4-A2-CSS
    BrandHoneywell Analytics
    Price: $6,346.00
    Quantity:

    SS4-A2-CSS Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, ATEX, Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, ATEX, IECE FOR Zone 1 (2) 3/4 NPT by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
    Honeywell Analytics Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, ATEX, Hydrogen & Non Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-AS2-C
    View Product Details >

    Honeywell Analytics Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, ATEX, Hydrogen & Non Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT - SS4-AS2-C




    Item #SS4-AS2-C
    BrandHoneywell Analytics
    Price: $5,543.00
    Quantity:

    SS4-AS2-C Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, ATEX, Hydrogen & Non Hydrocarbon Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT by Honeywell Analytics

    The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

    Fire Sentry SS4-A

    The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

    To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

    Fire Sentry SS4-AS

    The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

    Fire Sentry SS4-AUV

    The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

    Operation

    The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

    The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

    The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

    Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

    Fire Sentry SS4-A and SS4-AS Features:

    • Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
    • Built-in test for optical "through the lens" testing
    • False alarm immunity
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option
    • Meets SIL 2 requirements

    Fire Sentry SS4-AUV Features:

    • Senses solar-blind ultraviolet band
    • Built-in test for optical "through the lens" testing
    • Utilises long-life, ruggedised UV sensors
    • Detects hydrocarbon and non-hydrocarbon based fires
    • Wide field-of-view and solar-blind
    • Adjustable detector sensitivity
    • Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
    • Wide temperature range of operation
    • Compatible with standard approved fire alarm panels
    • Explosion-proof housing
    • Time programmable alarm verification
    • mA output option

    Applications include:

    • Petrochemical facilities and Refineries
    • Co-Generation plants
    • Aircraft hangars
    • Silane and Hydrogen gas storage
    • Gas Turbines and power plants
    • Gas compressor stations
    • Warehouses
    • Semiconductor
     
    Items per page:
    Sort by: